P0606 means the engine control module has detected an internal processor error during its routine self-test. The ECM continuously checks its own processor integrity, and this code indicates that test has failed, meaning the brain of your engine is malfunctioning and cannot be trusted.
DTC/P0606·Peugeot
P0606 on Peugeot: Causes, Symptoms and Fix Cost
Quick Answer
Critical SeverityNot safe to drivePeugeot
P0606 on a Peugeot means the engine control module has detected an internal processor error during its routine self-test. The ECM continuously checks its own processor integrity, and this code indicates that test has failed, meaning the brain of your engine is malfunctioning and cannot be trusted.
Repair cost on Peugeot€60 - €2450
What does P0606 mean on a Peugeot?
Peugeot 308
2007-2024The 308 with the 1.6 THP (EP6) engine uses a Bosch MEV17.4 ECU that is known for internal faults. P0606 on these models is often accompanied by anti-pollution system warnings. Specialist ECU repair services can reflow the solder joints on the processor for around 200-300 EUR.
What causes P0606 on a Peugeot?
Beyond the generic causes listed on the main P0606 page, these are the Peugeot-specific patterns we see most often:
Peugeot 308Bosch MEV17.4 internal solder joint failures
Peugeot 308EP6 engine ECU overheating under bonnet
How to diagnose P0606 on a Peugeot with OBD2
Follow these steps to pinpoint the root cause of P0606:
- Check battery voltage and charging system output. Verify the alternator produces 13.5-14.5V with engine running. Voltage irregularities can cause processor errors.
- Inspect the ECM connector for corroded, bent, or pushed-back pins. Clean with electrical contact cleaner and verify all pins make solid contact.
- Check for water intrusion around the ECM housing. Look for signs of moisture, white corrosion, or water stains on the ECM case and surrounding area.
- Clear the code and perform a full drive cycle. If P0606 returns immediately upon key-on, the ECM processor has failed internally and the unit needs replacement.
- Before replacing the ECM, verify power and ground circuits to the module meet specifications. A poor ground can mimic internal processor faults.
How much does P0606 cost to fix on a Peugeot? (EUR)
Estimated repair costs on a Peugeot (Peugeot costs align with the average for this code across makes).
Prices estimated as of May 2026. Costs vary by region, vehicle, and shop.
Related codes that often appear with P0606 on Peugeot
These codes commonly cluster with P0606 on Peugeot vehicles:
FAQ: P0606 on Peugeot
What does code P0606 mean?
P0606 means the engine control module's internal processor has failed its self-diagnostic test. The ECM runs continuous checks on its own hardware, and this code triggers when the processor produces incorrect results.
Can P0606 be fixed without replacing the ECU?
Sometimes. Check the ECM connector, grounds, and battery voltage first. In some cases, specialist ECU repair shops can fix circuit board faults for 200-500 EUR, saving you the cost of a full replacement.
How much does ECU replacement cost in Europe?
A new ECM typically costs 500-2000 EUR for the part, plus 150-450 EUR for programming and installation. Remanufactured units cost 30-50% less and are a good alternative.
Can a bad battery cause P0606?
Yes. Unstable voltage from a weak battery or failing alternator can cause the ECM processor to produce errors. Always test the battery and charging system before condemning the ECM.
Will my car start with P0606?
It depends on the severity of the processor fault. Some vehicles will start but run poorly, while others may not start at all or will stall shortly after starting.
Looking for the full P0606 reference (all makes, full diagnosis flow, complete repair cost matrix)?
See the main P0606 guideSkanyx · Peugeot
Diagnosing P0606 on your Peugeot?
Connect any Bluetooth OBD2 adapter, scan for codes, and get AI-powered diagnostics with severity ratings and repair cost estimates.
Download Skanyx