Skip to content
Skanyx
DTC/P0236·Ford

P0236 on Ford: Causes, Symptoms and Fix Cost

Quick Answer
Moderate SeverityNot safe to driveFord

P0236 on a Ford means the boost pressure sensor is producing a reading that does not make sense to the ECU, even though its voltage is still inside the normal range. The ECU checks it against the barometric and manifold pressure readings with the engine off, and against the boost it expects while driving; when they disagree it sets P0236. A faulty sensor is a common cause, but a boost leak, a contaminated sensing port or a turbo control fault can produce the same code. Most repairs cost between 40 and 200 euros.

Connect any standard Bluetooth OBD2 adapter to your Ford and Skanyx tells you what P0236 means on that engine, whether it is safe to keep driving, and what the fix should cost. Free on iPhone and Android.

Get Skanyx free

What does P0236 mean on a Ford?

The Quick Answer above is the generic definition. What follows is the model-specific detail for the Ford models that log P0236.

Ford Fiesta ST 1.6 EcoBoost

2013-2018

The Fiesta ST's 1.6 EcoBoost has two separate pressure sensors: a MAP sensor on the engine, reached after removing the engine cover, and a combined turbocharger boost pressure and charge air temperature (TCBP/CACT) sensor in the charge air ducting, reached from under the car. The boost sensor this code refers to is the TCBP/CACT sensor, so check which part you are buying, and compare its key-on reading with the MAP and barometric readings before replacing it.

What causes P0236 on a Ford?

Beyond the generic causes listed on the main P0236 page, these are the patterns noted for Ford models:

Ford Fiesta ST 1.6 EcoBoostFailed or contaminated TCBP/CACT sensor
Ford Fiesta ST 1.6 EcoBoostCharge air duct or intercooler leak

How to diagnose P0236 on a Ford with OBD2

Follow these steps to pinpoint the root cause of P0236:

  1. Read all stored codes and the freeze frame. If P0299 or P0234 is stored as well, boost really did go wrong and the sensor may be reporting it correctly; if P0236 is on its own, the sensor or its wiring is the stronger suspect
  2. Switch the ignition on without starting the engine and compare the boost sensor, MAP and barometric readings. With no boost in the system they should all read atmospheric pressure, roughly 95 to 105 kPa at sea level, within a few kPa of each other. A generic OBD2 reader shows these where the ECU exposes them. A boost sensor that reads clearly higher or lower than the other two with the engine off is faulty or has a wiring problem
  3. Start the engine and watch the boost reading at idle, then under load on a road test. It should sit near atmospheric at idle and rise smoothly as you accelerate. A reading that jumps, drops out or stays flat while the engine clearly pulls points at the sensor or its connector
  4. Remove the sensor and inspect the sensing port and the tip. Oil sludge or soot blocking the port slows or distorts the reading, so clean it and check the charge pipe for heavy oil, which can point at crankcase breather or turbo seal problems
  5. Perform a boost leak test by pressurising the intake system with compressed air at 0.5 to 1 bar and listening or using soapy water at every clamp, hose and the intercooler
  6. Back-probe the connector with the ignition on. The reference should read about 4.5 to 5.2 V and the sensor ground within about 0.1 V of battery negative. Wiggle the harness while watching the live reading to catch an intermittent fault
  7. If the sensor, wiring and boost system all check out, have the wastegate or turbo actuator checked. Actuator tests need manufacturer-level software; a generic OBD2 reader cannot run them

How much does P0236 cost to fix on a Ford? (EUR)

Estimated repair costs for P0236 in EUR, compiled across makes. Ford costs typically sit in the middle of each range.

Repair Parts Cost Labor Cost Total Estimate DIY Difficulty
Clean and reseat boost sensor connector, clean sensing port €0–€10 €0–€40 €0–€50 Easy
Replace boost pressure sensor €20–€80 €20–€60 €40–€140 Easy
Fix boost leak (tighten clamps, replace hose) €10–€80 €30–€120 €40–€200 Moderate
Repair boost sensor wiring or connector pins €10–€40 €60–€180 €70–€220 Moderate
Replace wastegate or boost pressure actuator €60–€250 €80–€250 €140–€500 Professional

Prices estimated as of March 2026. Costs vary by region, vehicle, and shop.

These codes are often seen alongside P0236 or point to related issues, on any make:

P0238FordP0299FordP0234P0106P0107FordP0046P0105

Looking for the full P0236 reference (all makes, full diagnosis flow, complete repair cost matrix)?

See the main P0236 guide
Skanyx · Ford

Diagnose P0236 on your Ford

Your car logged P0236. Skanyx reads it on any standard Bluetooth OBD2 adapter, tells you whether it is safe to keep driving, and breaks down the likely repair so you know the number before a shop quotes you. Free on iPhone and Android, and you do not need to be a mechanic to read it.

Get Skanyx free
Home