P0325 on Toyota: Causes, Symptoms and Fix Cost
Quick Answer
Safe to drive (short-term)
P0325 on a Toyota means the ECU sees an out-of-range voltage on the bank 1 knock sensor circuit. Without valid knock data the ECU defaults to conservative ignition timing, so you lose power and fuel economy.
- Severity
- Moderate · Electrical
- Typical repair cost, all makes
- €90-€1600
Connect a standard OBD2 adapter (Bluetooth LE on iPhone) to your Toyota and Skanyx tells you what P0325 means on that engine, whether it is safe to keep driving, and what the fix should cost. Free on iPhone and Android.
Get Skanyx freeWhat does P0325 mean on a Toyota?
The Quick Answer above is the generic definition. What follows is the model-specific detail for the Toyota models that log P0325.
Toyota Camry
2002-2011
1MZ-FE and 2GR-FE V6 engines are the classic P0325 case. The sensor sits in the valley under the intake manifold. The sensor and its sub-harness are separate parts, and both sit in the same heat under the manifold, so check the harness while the intake is off rather than doing the job twice.
What causes P0325 on a Toyota?
Beyond the generic causes listed on the main P0325 page, these are the patterns noted for Toyota models:
Original sensor internal failure typical past 150,000 km
: Toyota Camry
Sub-harness insulation cracks from heat cycling under the intake
: Toyota Camry
Corroded connector after intake gasket or coolant work
: Toyota Camry
How to diagnose P0325 on a Toyota with OBD2
- Scan the ECU and record freeze frame (RPM, load, coolant temp) at the moment the code set
- Visually inspect the knock sensor connector and pigtail for corrosion, oil, coolant or chafing
- Measure sensor resistance with a multimeter. Depending on design, knock sensors read anywhere from roughly 100 kΩ to several megohms, and some show no continuity at all, so compare with the figure for your engine rather than a generic number. A reading near zero points to a shorted sensor
- Backprobe the signal and ground wires at the ECU connector and check continuity and shield integrity to the sensor
- With manufacturer-level software reading knock sensor voltage or knock counts live (a generic OBD2 reader does not show these), tap the block near the sensor with a small wrench to confirm the ECU sees a response
- If the sensor and wiring pass, remove the sensor, clean the mounting boss free of paint and rust, and torque to spec (typically 20-25 Nm for Toyota, ~20 Nm for GM LS)
- Clear the code and drive under load (moderate acceleration, 2,500-4,000 RPM); if P0325 returns immediately with the sensor and harness confirmed good, suspect the ECU input
How much does P0325 cost to fix on a Toyota? (EUR)
Estimated repair costs for P0325 in EUR, compiled across makes. Expect Toyota parts and labour towards the upper end of each range.
| Repair | Parts Cost | Labor Cost | Total Estimate | DIY Difficulty |
|---|---|---|---|---|
| Knock sensor replacement on an accessible 4-cylinder (side of block) | €40–€120 | €50–€140 | €90–€260 | Moderate |
| Knock sensor replacement under the intake manifold (V6/V8) | €60–€180 | €300–€700 | €360–€880 | Professional |
| Wiring or connector repair (pin replacement, splice, dielectric reseal) | €15–€80 | €80–€200 | €95–€280 | Moderate |
| Knock sensor sub-harness kit (GM LS valley harness or equivalent) | €70–€160 | €280–€600 | €350–€760 | Professional |
| ECU/PCM replacement and programming (last resort after circuit verified) | €400–€1200 | €150–€400 | €550–€1600 | Professional |
Prices estimated as of October 2026. Costs vary by region, vehicle, and shop.
Codes related to P0325
These codes are often seen alongside P0325 or point to related issues, on any make:
Looking for the full P0325 reference (all makes, full diagnosis flow, complete repair cost matrix)? See the main P0325 guide