U0100 on Chevrolet: Causes, Symptoms and Fix Cost
Quick Answer
Not safe to drive
U0100 on a Chevrolet sets when another control module stops receiving CAN messages from the ECM/PCM. It's a communication failure, not an engine mechanical fault, and it usually prevents the car from starting or keeps it in severe limp mode.
- Severity
- Critical · Electrical
- Typical repair cost, all makes
- €5-€2200
Connect a standard OBD2 adapter (Bluetooth LE on iPhone) to your Chevrolet and Skanyx tells you what U0100 means on that engine, whether it is safe to keep driving, and what the fix should cost. Free on iPhone and Android.
Get Skanyx freeWhat does U0100 mean on a Chevrolet?
The Quick Answer above is the generic definition. What follows is the model-specific detail for the Chevrolet models that log U0100.
Chevrolet Silverado 1500 (GMT900)
2007-2013
GMT900 trucks use GMLAN (single-wire and dual-wire). U0100 commonly traces to rodent damage on the engine harness routed above the intake manifold, or a failed BCM taking down the low-speed GMLAN bus.
What causes U0100 on a Chevrolet?
Beyond the generic causes listed on the main U0100 page, these are the patterns noted for Chevrolet models:
Rodent damage to CAN wires along the top of the intake
: Chevrolet Silverado 1500 (GMT900)
BCM failure disrupting the low-speed GMLAN bus
: Chevrolet Silverado 1500 (GMT900)
Corroded battery cable ends causing crank voltage drop below 9V
: Chevrolet Silverado 1500 (GMT900)
How to diagnose U0100 on a Chevrolet with OBD2
- Load-test the battery and confirm at least 12.4V resting, 9.6V minimum during crank. Bus faults below 11V during crank are common and mask the real cause.
- Scan every module and log which ones report U0100 plus any companion U-codes. One reporter points to wiring at that module, multiple reporters point to the ECM or the bus itself.
- Check ECM-related fuses and relays in both the underhood and interior fuse boxes against the wiring diagram, including battery-fed and ignition-fed circuits.
- Measure ECM power and ground at the module connector, key on: battery voltage on B+ pins, under 0.1V drop on ground pins referenced to the negative battery post.
- With the ignition off, give the modules a couple of minutes to go to sleep, then measure resistance across DLC pins 6 and 14. Expect about 60 ohms (two 120-ohm terminating resistors in parallel). 120 ohms means one terminator or half the bus is missing, and much lower means a short.
- Backprobe CAN-H and CAN-L at the ECM connector, key on. Both lines should idle around 2.5V, with CAN-H rising and CAN-L falling during traffic. An oscilloscope makes this obvious.
- If the bus is shorted or flooded, disconnect suspect modules one at a time until communication returns to identify the offender.
- Only after power, grounds, fuses, and bus wiring are verified good, swap in a known-good ECM to confirm before ordering a replacement.
How much does U0100 cost to fix on a Chevrolet? (EUR)
Estimated repair costs for U0100 in EUR, compiled across makes. Expect Chevrolet parts and labour towards the upper end of each range.
| Repair | Parts Cost | Labor Cost | Total Estimate | DIY Difficulty |
|---|---|---|---|---|
| Replace blown fuse, clean grounds, or replace battery | €5–€200 | €0–€60 | €5–€260 | Easy |
| Repair damaged CAN bus wiring or reterminate ECM connector pins | €10–€80 | €80–€300 | €90–€380 | Moderate |
| Replace faulty peripheral module (BCM, gateway, TCM) flooding the bus | €200–€900 | €100–€300 | €300–€1200 | Professional |
| Replace and program ECM/PCM including immobilizer sync | €600–€1800 | €150–€400 | €750–€2200 | Professional |
Prices estimated as of October 2026. Costs vary by region, vehicle, and shop.
Codes related to U0100
These codes are often seen alongside U0100 or point to related issues, on any make:
Looking for the full U0100 reference (all makes, full diagnosis flow, complete repair cost matrix)? See the main U0100 guide