P0011 on Nissan: Causes, Symptoms and Fix Cost

Quick Answer

Safe to drive (short-term)

P0011 on a Nissan means the intake camshaft on bank 1 is positioned more advanced than the ECU commanded it to be. The variable valve timing system is not responding correctly, typically due to oil flow issues, a faulty VVT solenoid, or a stretched timing chain affecting cam position.

Severity: Moderate · Emissions
Typical repair cost, all makes: €40-€1150

Connect a standard OBD2 adapter (Bluetooth LE on iPhone) to your Nissan and Skanyx tells you what P0011 means on that engine, whether it is safe to keep driving, and what the fix should cost. Free on iPhone and Android.

Get Skanyx free

What does P0011 mean on a Nissan?

The Quick Answer above is the generic definition. What follows is the model-specific detail for the Nissan models that log P0011.

Nissan Qashqai

2007-2024

On the Nissan MR20 and HR16 in the Qashqai and Juke, and the QR25 in the X-Trail and Altima, P0011 usually means the intake valve timing control (VTC) solenoid or oil control valve is stuck or clogged with sludge, often after extended oil-change intervals. The VTC actuator on the front of the camshaft is also a known cold-start rattle point on these engines, so check oil condition and level first.

What causes P0011 on a Nissan?

Beyond the generic causes listed on the main P0011 page, these are the patterns noted for Nissan models:

Clogged or stuck intake valve timing control (VTC) solenoid, often from old oil
: Nissan Qashqai
Worn VTC cam actuator causing cold-start rattle on QR/MR engines
: Nissan Qashqai
Low oil level or wrong viscosity slowing the variable valve timing response
: Nissan Qashqai

How to diagnose P0011 on a Nissan with OBD2

Follow these steps to pinpoint the root cause of P0011:

Check engine oil level and condition. Low, dirty, or incorrect viscosity oil is the most common cause. Change oil if overdue and clear the code
Read the actual camshaft advance angle and the target angle commanded by the ECU with manufacturer-level software (actual and target cam angles are not part of the standard OBD2 data set; a generic reader shows the code, freeze frame and fuel trims). A persistent gap between the two confirms the VVT system is not following commands
Inspect and test the VVT solenoid. Measure resistance (typically 6-13 ohms) and check for clogged screens. Commanding the solenoid on and off is an actuator test that needs manufacturer-level software
Listen for timing chain rattle on cold startup. A stretched chain will cause a brief rattle that fades as oil pressure builds
If the solenoid and oil are fine, inspect timing chain stretch with a scope or by checking timing marks alignment

How much does P0011 cost to fix on a Nissan? (EUR)

Estimated repair costs for P0011 in EUR, compiled across makes. Nissan costs typically sit in the middle of each range.

Repair	Parts Cost	Labor Cost	Total Estimate	DIY Difficulty
Engine oil and filter change (if dirty oil is the cause)	€20–€60	€20–€50	€40–€110	Easy
Replace VVT solenoid	€25–€130	€40–€120	€65–€250	Moderate
Replace timing chain and tensioner	€100–€350	€300–€800	€400–€1150	Professional
Replace camshaft phaser/actuator	€80–€300	€200–€600	€280–€900	Professional

Prices estimated as of March 2026. Costs vary by region, vehicle, and shop.

These codes are often seen alongside P0011 or point to related issues, on any make:

Looking for the full P0011 reference (all makes, full diagnosis flow, complete repair cost matrix)? See the main P0011 guide

Diagnose P0011 on your Nissan

Your car logged P0011. Skanyx reads it on a standard OBD2 adapter (Bluetooth LE on iPhone), tells you whether it is safe to keep driving, and shows the €40-€1150 repair range so you know the number before a shop quotes you. Free on iPhone and Android, and you do not need to be a mechanic to read it.