P0136 means the downstream oxygen sensor on Bank 1 (post-catalyst, Sensor 2) is producing a voltage signal outside the expected operating range. This sensor monitors how well the catalytic converter is cleaning exhaust gases. A failing sensor or a degrading converter can both trigger this code.
DTC/P0136·Audi
P0136 on Audi: Causes, Symptoms and Fix Cost
Quick Answer
Moderate SeveritySafe to drive (short-term)Audi
P0136 on a Audi means the downstream oxygen sensor on Bank 1 (post-catalyst, Sensor 2) is producing a voltage signal outside the expected operating range. This sensor monitors how well the catalytic converter is cleaning exhaust gases. A failing sensor or a degrading converter can both trigger this code.
Repair cost on Audi€56 - €388
What does P0136 mean on a Audi?
Audi A4
2006–2024On the B7 and B8 A4 with the 2.0 TFSI (EA113 and EA888), carbon buildup on the intake valves causes inconsistent combustion, which the downstream sensor reports as drift. Walnut blast the intake before condemning the sensor on any TFSI over 80,000 km. The connector lives near the gearbox bellhousing and is awkward to reach from above.
What causes P0136 on a Audi?
Beyond the generic causes listed on the main P0136 page, these are the Audi-specific patterns we see most often:
Audi A4Carbon buildup on 2.0 TFSI intake valves causing combustion drift
Audi A4Connector access difficulty leading to incomplete repairs
How to diagnose P0136 on a Audi with OBD2
Follow these steps to pinpoint the root cause of P0136:
- Read freeze frame data to capture the engine conditions when the code was set (RPM, coolant temp, load)
- Inspect the exhaust system between the catalytic converter and the downstream sensor for cracks, loose clamps, or gasket leaks
- Inspect the Bank 1 Sensor 2 connector and wiring for corrosion, heat damage, or chafing against the heat shield
- Use a scan tool to view live O2 sensor data. The downstream sensor should show a relatively flat voltage around 0.6–0.8V at operating temperature, not the rapid switching of the upstream sensor
- Compare upstream vs downstream waveforms. If both switch identically, the converter is likely failing. If the downstream is erratic or stuck, replace the sensor
How much does P0136 cost to fix on a Audi? (EUR)
Estimated repair costs on a Audi (Audi parts and labour typically run 25% above the average for this code).
Prices estimated as of May 2026. Costs vary by region, vehicle, and shop.
Related codes that often appear with P0136 on Audi
These codes commonly cluster with P0136 on Audi vehicles:
FAQ: P0136 on Audi
Can I drive with P0136?
Yes, for short distances. The downstream sensor mainly monitors catalytic converter efficiency, so it does not directly affect how the engine runs. However, you will fail an emissions test and may miss a developing converter issue if you ignore it for weeks.
How long does a downstream O2 sensor last?
Most downstream O2 sensors last 130,000–200,000 km because they operate in cooler exhaust gas after the catalytic converter. The upstream sensor usually fails first.
Is the upstream or downstream sensor more important?
The upstream sensor is more critical because it controls real-time fuel mixture. The downstream sensor monitors converter health and only makes small fuel trim corrections. A failed downstream sensor will not stop the car from running properly.
Will P0136 fail an emissions test?
Yes. Any active check engine light is an automatic emissions failure in most EU countries, regardless of the actual readiness monitor status.
Looking for the full P0136 reference (all makes, full diagnosis flow, complete repair cost matrix)?
See the main P0136 guideSkanyx · Audi
Diagnosing P0136 on your Audi?
Connect any Bluetooth OBD2 adapter, scan for codes, and get AI-powered diagnostics with severity ratings and repair cost estimates.
Download Skanyx