Skip to content
Skanyx

P0322 on Volkswagen: Causes, Symptoms and Fix Cost

Quick Answer

Not safe to drive

P0322 on a Volkswagen means the engine computer is not receiving any engine speed signal. On most modern cars that signal comes from the crankshaft position sensor, and on older cars it can come from the distributor or an ignition module. With no speed signal the computer cannot time spark or fuel, so the engine usually will not start or will stall. VW, Audi, Skoda and SEAT apps often show this code as P032200; the last two digits are a failure-type byte.

Severity
Critical · Ignition
Typical repair cost, all makes
€70-€1500

Connect a standard OBD2 adapter (Bluetooth LE on iPhone) to your Volkswagen and Skanyx tells you what P0322 means on that engine, whether it is safe to keep driving, and what the fix should cost. Free on iPhone and Android.

Get Skanyx free

What does P0322 mean on a Volkswagen?

The Quick Answer above is the generic definition. What follows is the model-specific detail for the Volkswagen models that log P0322.

Volkswagen Tiguan

2007-2018

Volkswagen Group software reports P0322 as "Engine Speed Sensor (G28): No Signal", and Ross-Tech notes that G28 is also the crankshaft position reference sensor. It lists a loose or faulty G28 as the causes and documents a 2012 first-generation Tiguan where coolant inside the engine control module set G28 codes and caused intermittent stalling, so check the wiring and the module for oil or coolant before condemning only the sensor.

What causes P0322 on a Volkswagen?

Beyond the generic causes listed on the main P0322 page, these are the patterns noted for Volkswagen models:

  • Loose or faulty G28 engine speed sensor

    : Volkswagen Tiguan

  • Oil or coolant damaging the harness or the engine control module

    : Volkswagen Tiguan

How to diagnose P0322 on a Volkswagen with OBD2

Follow these steps to pinpoint the root cause of P0322:

  1. Read all codes and check whether P0335, P0336, P0339 or cam sensor codes are stored too
  2. Crank the engine while watching engine speed on a scan tool: a reading of zero while the starter turns means the signal is truly missing
  3. Inspect the sensor connector and wiring for oil, coolant, corrosion, chafing and broken wires
  4. Check that the sensor is fitted and tightly mounted and that its tip is clean
  5. Test the sensor supply, ground and signal against the manufacturer specification
  6. On older cars with a distributor, inspect the pickup and ignition module
  7. Inspect the toothed wheel for damage and check the engine control unit for water or coolant if the rest tests good

How much does P0322 cost to fix on a Volkswagen? (EUR)

Estimated repair costs for P0322 in EUR, compiled across makes. Expect Volkswagen parts and labour towards the upper end of each range.

Repair Parts Cost Labor Cost Total Estimate DIY Difficulty
Replace engine speed (crankshaft position) sensor €20–€100 €50–€200 €70–€300 Moderate
Repair wiring or connector to sensor €10–€50 €60–€180 €70–€230 Moderate
Replace reluctor ring (tone wheel) €30–€120 €200–€600 €230–€720 Professional
Replace engine control unit with programming €400–€1200 €100–€300 €500–€1500 Professional

Prices estimated as of March 2026. Costs vary by region, vehicle, and shop.

These codes are often seen alongside P0322 or point to related issues, on any make:

Looking for the full P0322 reference (all makes, full diagnosis flow, complete repair cost matrix)? See the main P0322 guide

Diagnose P0322 on your Volkswagen

Your car logged P0322. Skanyx reads it on a standard OBD2 adapter (Bluetooth LE on iPhone), tells you whether it is safe to keep driving, and shows the €70-€1500 repair range so you know the number before a shop quotes you. Free on iPhone and Android, and you do not need to be a mechanic to read it.

Get Skanyx free